road_case_tutorial
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
road_case_tutorial [2024/04/18 16:43] – old revision restored (2024/04/15 13:48) enowery | road_case_tutorial [2024/04/21 22:10] (current) – [Getting Started] enowery | ||
---|---|---|---|
Line 55: | Line 55: | ||
__You can buy most of the road case specific supplies, like the aluminum extrusions, ball corners, handles, latches, etc., online from various places. I bought mine from << | __You can buy most of the road case specific supplies, like the aluminum extrusions, ball corners, handles, latches, etc., online from various places. I bought mine from << | ||
- | Here is an example of my Bill of Materials | + | ^ PART NAME ^ SKU or ASIN ^ QTY ^ PRICE (USD per unit) ^ URL ^ |
- | {{ :roadcase_bom.png?nolink&400 |}} | + | | 3/8" Double Angle Corner Extrusion |
+ | | Handle (Surface Mounted) | ||
+ | | Latch (Surface Mounted) | ||
+ | | Medium Ball Corner | ||
+ | | Tongue and Groove Extrusion | ||
+ | | POP Rivet for 3/8" & 1/2" Walls | 6690 | 150-200 | ||
+ | | Backing Washer | ||
+ | | 3/16" Drill bit | B0BPC6WQLC | ||
+ | | Black Enamel Spray | # | ||
+ | | Polyurethane Spray Coating | ||
+ | | Black Bed Liner Spray | #4860951 | 1 | 16.96 | https:// | ||
+ | | Plywood Sheet | # | ||
+ | | | ||
===== Getting Started ===== | ===== Getting Started ===== | ||
Line 71: | Line 83: | ||
===Step 3: Cut Extrusions=== | ===Step 3: Cut Extrusions=== | ||
- | Next, measure out the aluminum extrusions for all corners | + | Next, measure out the aluminum extrusions for all edges of the box. Start to measure the edges from an inch inside all corners. This will leave your extrusions 2 inches shorter than their edges. |
- | __Make it easier on yourself, | + | |
+ | Using a miter saw, cut the extrusions to your measured length. | ||
+ | __Make it easier on yourself, | ||
{{ : | {{ : | ||
Line 78: | Line 92: | ||
===Step 4: Drill Holes and Rivet=== | ===Step 4: Drill Holes and Rivet=== | ||
- | After lining up the extrusions with the wood. Drill holes through the extrusion and wood at even intervals. Next, put the rivets into the holes, with the nail part sticking towards the outside of the case. Rivet them down to attach the extrusions to the wood. NOTE, if you have a case with multiple parts, like a lid, make sure to leave the edges that connect the two bare for now. We will attach tongue and groove extrusions to that later. **To remove a rivet, use the same drill bit used to drill the initial hole and drill out the rivet** | + | After lining up the extrusions with the wood. Drill holes through the extrusion and wood at even intervals |
{{ : | {{ : | ||
Line 100: | Line 114: | ||
For the lining of my roadcase, I used this truck bed liner spray. | For the lining of my roadcase, I used this truck bed liner spray. | ||
- | {{ : | + | {{ :roadcase_truck_spray.png? |
+ | |||
+ | Tape off the edges of your road case and apply the liner of choice, following the instructions. | ||
+ | |||
+ | {{ : | ||
---- | ---- |
road_case_tutorial.1713483809.txt.gz · Last modified: 2024/04/18 16:43 by enowery