Differences

This shows you the differences between two versions of the page.

--- how_to_screen_print_dasl_logo [2017/06/09 21:00] – [Screen Printing - Negative Method] jihyunlee
+++ how_to_screen_print_dasl_logo [2017/06/10 22:13] (current) – [Failures and success of screen printing] jihyunlee
@@ Line 8: / Line 8: @@
 {{:jihyun:스1.jpg?300|}}
 \\
-The photo above depicts DASL logo screen printed on the black fabric . This tutorial shows you how to do the negative method screen printing and takes approximately half an hour to complete.
+The photo above depicts DASL logo screen printed on the black fabric . This tutorial shows you how to do the screen printing in negative method and takes approximately half an hour to complete.
 \\
 ===== Motivation and Audience =====
-This tutorial's motivation is to <fill in the blank>. Readers of this tutorial assumes the reader has the following background and interests:
+This tutorial's motivation is to teach students to do screen printing. Readers of this tutorial assumes the reader has the following background and interests:
 <fc blue>
@@ Line 118: / Line 118: @@
 \\
 . After printing wash the mesh and squeegee before the paint dries.
-==== Programming ====
+===== Failures and success of screen printing =====
-A link to the source code can be found <provide URL to your code, probably saved in this DASL Wiki>.
 \\
-The goal of the code is <brief explanation>.  It works in the following way
+There are some conditions that you might fail during the screen printing. If you keep in mind followings below you will be able to screen print professionally.
 \\
-----
-<!- Insert a snippet of your code here.  Try to keep to less than 0.5 page long -->
-----
 \\
-The snippet above serves to <fill in the blank>. It does this by <fill in the blank>.
+**- While screen printing -**
+\\
+\\
+{{::스20.png?300|}}
+\\
+. Don't change the location after spreading the paint.
+\\
+You will not be able to use the paper again. If you use that paper again it will cause smudges like the picture.
+\\
+\\
+{{:jihyun:스21.jpg?300|}}
+\\
+. Put the fabric on the flat place. And check there is no wrinkles. Or it will look like the picture.
+\\
+\\
+{{:jihyun:tm22.png?300|}}
+\\
+. Do not spread the paint too wide from the logo. You will accidentally stick out the paint like the picture.
+\\
+. Also use the proper amount of paint to spread evenly. You can see in the picture that the some parts are not painted completely.
+\\
+\\
+{{:jihyun:스24.jpg?300|}}
+\\
+. So far it is said not to use the paint too little, do not use it too much as well. Paints tenacity is high so when you put too much paint and remove the mesh, paint will stretch and be every where.
+\\
 \\
 ----
-<!- Insert another snippet of your code here.  Try to keep to less than 0.5 page long -->
+** - Choosing the material - **
-----
+\\
-Next, the code does <fill in the blank>.  It does this by <fill in the blank>.
+\\
-<!-- Keep entering snippets of code and descriptions until you've given enough for a reader to understand how it works -->
+{{:jihyun:스25.jpg?300|}}
-//
+\\
-//
+{{:jihyun:스26.jpg?300|}}
+\\
+. Use the material that can absorb paint like the first picture.
+\\
+Use the material that is flat.
+\\
+\\
+. If you use the material that cannot absorb the paint it will be like the second picture.
+\\
+If you don't use the material that is not flat it will be like the second picture.
 ==== Final Words ====