hitechnic_angle_encoder
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
hitechnic_angle_encoder [2017/08/21 13:16] – [Motivation and Audience] yuhanghe | hitechnic_angle_encoder [2017/08/28 17:25] (current) – [Motivation and Audience] yuhanghe | ||
---|---|---|---|
Line 32: | Line 32: | ||
\\ \\ | \\ \\ | ||
The rest of this tutorial is presented as follows: | The rest of this tutorial is presented as follows: | ||
- | * [[tutorialTemplate#partsListAndSources|Parts List and Sources]] | + | * [[hitechnic_angle_encoder#programming|Programming]] |
- | * [[tutorialTemplate#construction|Construction]] | + | * [[hitechnic_angle_encoder#example|Example]] |
- | * Programming <!- delete this line if not applicable -> | + | * [[hitechnic_angle_encoder# |
- | * Final Words | + | |
- | ==== Parts List and Sources | + | ===== Programming ===== |
- | US-based vendors | + | To use LabVIEW |
- | \\ | + | |
- | To complete this tutorial, you'll need the following items <!-- in table below, replace ??? with relevant information and add additional lines if necessary --> | + | |
- | <!-- Alternatively create: (1) a Google XLS document that's publicly viewable and provide link; and (2) a PDF version of the Google XLS, store the PDF file in your site, and provide link to it --> | + | To access block diagram nodes for Angle Sensor, go to '' |
+ | {{ : | ||
- | \\ | + | To receive inputs from Angle Sensor, use the '' |
+ | {{ : | ||
- | ^PART NAME/ | + | HT Read have four different implementations: |
- | | Smooth-on Silicone Mold Rubber | + | |
- | | <???> | + | |
- | | <???> | + | |
- | | <???> | + | |
- | | <???> | + | |
- | \\ | + | To reset the angle and accumulated angle, use the HT config node, which can be assessed under '' |
- | <!-- Replace | + | \\ |
- | Here is the [[https:// | + | '' |
- | \\ | + | |
- | <!-- Replace the filename | + | *'' |
- | Here is the {{:tutorialtemplategooglexlssamplepdf.pdf| list as a PDF file}} | + | |
- | \\ | + | |
- | ==== Construction | + | {{ : |
+ | ===== Example ===== | ||
- | This section gives step-by-step instructions along with photos to <fill in the blank>. (If a circuit-building tutorial:) A schematic to construct <fill in the blank> is shown here <add image>. <Add hyperlink to PDF of schematic> | + | Here is a simple example that displays |
- | \\ | + | |
- | \\ | + | |
- | **Step 1** | + | |
- | \\ | + | |
- | \\ | + | |
- | <Add photos to make step easier to understand> | + | |
- | \\ | + | |
- | \\ | + | |
- | **Step 2** | + | |
- | \\ | + | |
- | \\ | + | |
- | < | + | |
- | \\ | + | |
- | ==== Programming ==== | + | |
- | A link to the source code can be found <provide URL to your code, probably saved in this DASL Wiki>. | + | {{ : |
- | \\ | + | {{ : |
- | The goal of the code is <brief explanation> | + | |
- | \\ | + | |
- | ---- | + | |
- | <!- Insert a snippet of your code here. Try to keep to less than 0.5 page long --> | + | |
- | ---- | + | |
- | \\ | + | |
- | The snippet above serves to <fill in the blank>. It does this by <fill in the blank> | + | |
- | \\ | + | |
- | ---- | + | |
- | <!- Insert another snippet of your code here. Try to keep to less than 0.5 page long --> | + | |
- | ---- | + | |
- | Next, the code does <fill in the blank> | + | |
- | <!-- Keep entering snippets of code and descriptions until you've given enough for a reader to understand how it works --> | + | |
- | // | + | |
- | // | + | |
- | ==== Final Words ==== | + | |
- | This tutorial' | + | |
- | \\ | + | |
- | \\ | + | |
- | Speculating future work derived from this tutorial, includes <fill in the blank>. In the big picture, the problem of <fill in the blank> can be solved with this tutorial. | + | ===== Final Words ===== |
+ | |||
+ | This tutorial' | ||
\\ | \\ | ||
\\ | \\ | ||
- | For questions, clarifications, | + | For questions, clarifications, |
hitechnic_angle_encoder.txt · Last modified: 2017/08/28 17:25 by yuhanghe