road_case_tutorial
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| road_case_tutorial [2024/04/18 14:38] – [Materials Needed] enowery | road_case_tutorial [2024/04/21 22:10] (current) – [Getting Started] enowery | ||
|---|---|---|---|
| Line 32: | Line 32: | ||
| * **Accessories** - There are latches and handles that come mounted to a back plate already. If you get those, you will have to cut holes in the wood to set those in. | * **Accessories** - There are latches and handles that come mounted to a back plate already. If you get those, you will have to cut holes in the wood to set those in. | ||
| - | |===== Materials Needed ===== | + | ===== Materials Needed ===== |
| __Note that this section will vary with the design of your own road case. From here on, everything is in reference to my own road case.__ | __Note that this section will vary with the design of your own road case. From here on, everything is in reference to my own road case.__ | ||
| Line 55: | Line 55: | ||
| __You can buy most of the road case specific supplies, like the aluminum extrusions, ball corners, handles, latches, etc., online from various places. I bought mine from << | __You can buy most of the road case specific supplies, like the aluminum extrusions, ball corners, handles, latches, etc., online from various places. I bought mine from << | ||
| - | \\ | + | ^ PART NAME ^ SKU or ASIN ^ QTY ^ PRICE (USD per unit) ^ URL ^ |
| + | | 3/8" Double Angle Corner Extrusion | ||
| + | | Handle (Surface Mounted) | ||
| + | | Latch (Surface Mounted) | ||
| + | | Medium Ball Corner | ||
| + | | Tongue and Groove Extrusion | ||
| + | | POP Rivet for 3/8" & 1/2" Walls | 6690 | 150-200 | ||
| + | | Backing Washer | ||
| + | | 3/16" Drill bit | B0BPC6WQLC | ||
| + | | Black Enamel Spray | # | ||
| + | | Polyurethane Spray Coating | ||
| + | | Black Bed Liner Spray | #4860951 | 1 | 16.96 | https:// | ||
| + | | Plywood Sheet | # | ||
| + | | | ||
| - | ^PART NAME ^SKU/PART NUMBER | ||
| - | |3/8" Double Angle Corner Extrusion | ||
| ===== Getting Started ===== | ===== Getting Started ===== | ||
| Line 72: | Line 83: | ||
| ===Step 3: Cut Extrusions=== | ===Step 3: Cut Extrusions=== | ||
| - | Next, measure out the aluminum extrusions for all corners | + | Next, measure out the aluminum extrusions for all edges of the box. Start to measure the edges from an inch inside all corners. This will leave your extrusions 2 inches shorter than their edges. |
| - | __Make it easier on yourself, | + | |
| + | Using a miter saw, cut the extrusions to your measured length. | ||
| + | __Make it easier on yourself, | ||
| {{ : | {{ : | ||
| Line 79: | Line 92: | ||
| ===Step 4: Drill Holes and Rivet=== | ===Step 4: Drill Holes and Rivet=== | ||
| - | After lining up the extrusions with the wood. Drill holes through the extrusion and wood at even intervals. Next, put the rivets into the holes, with the nail part sticking towards the outside of the case. Rivet them down to attach the extrusions to the wood. NOTE, if you have a case with multiple parts, like a lid, make sure to leave the edges that connect the two bare for now. We will attach tongue and groove extrusions to that later. **To remove a rivet, use the same drill bit used to drill the initial hole and drill out the rivet** | + | After lining up the extrusions with the wood. Drill holes through the extrusion and wood at even intervals |
| {{ : | {{ : | ||
| Line 101: | Line 114: | ||
| For the lining of my roadcase, I used this truck bed liner spray. | For the lining of my roadcase, I used this truck bed liner spray. | ||
| - | {{ : | + | {{ :roadcase_truck_spray.png? |
| + | |||
| + | Tape off the edges of your road case and apply the liner of choice, following the instructions. | ||
| + | |||
| + | {{ : | ||
| ---- | ---- | ||
road_case_tutorial.1713476306.txt.gz · Last modified: 2024/04/18 14:38 by enowery