cnc_setting_up_tutorial_0
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
cnc_setting_up_tutorial_0 [2017/01/21 10:24] – jeanvaz | cnc_setting_up_tutorial_0 [2017/04/20 14:23] (current) – jeanvaz | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== CNC Tormach PCNC 1100 Tutorial 0 ====== | ====== CNC Tormach PCNC 1100 Tutorial 0 ====== | ||
- | **Author:** Jean Chagas Vaz **Email:** chagasva@unlv.nevada.edu | + | ====== DASL 104: Humanoid Robotics ====== |
- | \\ | + | |
- | **Date:** Last modified on 01/18/17 | + | **Author: |
- | \\ | + | **Date:** Last modified on 04/20/2017 \\ |
**Keywords: | **Keywords: | ||
\\ | \\ | ||
Line 32: | Line 32: | ||
==== Procedure ==== | ==== Procedure ==== | ||
+ | |||
+ | Before you start: <fc red> | ||
+ | |||
+ | {{: | ||
\\ | \\ | ||
Line 62: | Line 66: | ||
<fc red> pressing the green button </fc> (image on the left) | <fc red> pressing the green button </fc> (image on the left) | ||
\\ | \\ | ||
- | {{: | + | |
- | \\Make sure to push the RESET button on the screen until you hear a characteristic sound. (image on the left) | + | {{: |
+ | |||
+ | |||
+ | Make sure to push the RESET button on the screen until you hear a characteristic sound. (image on the left) | ||
\\ | \\ | ||
- | Figure | + | Figure: Setting up the machine. |
\\ | \\ | ||
\\ | \\ | ||
**Step 4** | **Step 4** | ||
+ | \\Once the machine has been properly rested, make sure to reference all the 3 axis | ||
\\ | \\ | ||
+ | |||
+ | {{: | ||
\\ | \\ | ||
- | {{: | ||
- | \\ | ||
- | Figure 4: ..... | ||
- | Next, .... | + | Now you should be able to move the machine. |
\\ | \\ | ||
\\ | \\ | ||
**Step 5** | **Step 5** | ||
+ | \\Using the jog shuttle select the axis which you want to move (figure on the left). Once you have selected the axis the the main screen should indicate the axis chosen. | ||
\\ | \\ | ||
+ | {{: | ||
\\ | \\ | ||
- | {{:? | ||
- | \\ | ||
- | Figure 5: ..... | ||
- | Next, ...... | + | This will let you to adjust the machine accordingly with your preference. |
\\ | \\ | ||
\\ | \\ | ||
+ | |||
+ | ==== Turning off ==== | ||
+ | |||
**Step 6** | **Step 6** | ||
+ | \\In order to safely turn the CNC machine off: Push the e-stop. A message will pop up on the screen indicating that the shut off procedure can go on. | ||
\\ | \\ | ||
+ | {{: | ||
- | Now ...... | + | Than on the computer press the EXIT button. Finally press the OKAY button to shut the machine down. |
- | \\ | + | {{:dsc_5549.jpg? |
- | \\ | + | |
- | **Step 7** | + | Once the " |
- | \\ | + | {{: |
- | When .... | ||
\\ | \\ | ||
\\ | \\ | ||
- | **Step 8** | ||
- | \\ | ||
- | \\ | ||
- | {{:? | ||
- | \\ | ||
- | Figure 8: ...... | ||
- | |||
- | Start by setting ..... | ||
+ | ==== Videos ==== | ||
\\ | \\ | ||
- | \\ | + | {{youtube> |
- | **Step 9** | + | |
- | \\ | + | |
- | Next, | + | {{youtube> |
- | + | ||
- | + | ||
- | \\ | + | |
- | {{youtube> | + | |
// | // | ||
// | // | ||
==== Commentaries ==== | ==== Commentaries ==== | ||
- | This tutorial' | + | This tutorial' |
\\ | \\ | ||
\\ | \\ | ||
- | dfhkjhsdfkjksdfkj | + | |
\\ | \\ | ||
\\ | \\ |
cnc_setting_up_tutorial_0.1485023067.txt.gz · Last modified: 2017/01/21 10:24 by jeanvaz